Directions for Tube Bracelet

Your kit contains:
1 24-inch piece of .015 beading wire
2 crimp beads
2 metal wire guards (look like horse shoes) 
1 magnet clasp
4 3x2mm rondelle metal beads
4 3mm round metal beads
4 2x38mm metal tubes
6 metal flat heishi spacer beads
10 colored bracelet beads
1 focal bead

You will need the following tools:
Chain nose pliers
Cutters

Step 1) Attach clasp to wire guard with crimp:
Thread the beading wire through one tube of the wire guard from the bottom, and then down the second tube from the top. (Note: if you are unfamiliar with wire guards, they are horse-shoe shaped with a hollow tube portion at both ends connected by an open u-shaped channel between them.)

Move the wire guard to the center of the beading wire. Now slip one ring of your magnet clasp over one end of the beading wire and bring it up into wire guard so it rests around the u-shaped channel. Once the magnet clasp is attached, bring both ends of the beading wire through the crimp. Pinch the two tube portions of the wire guard together so they are touching, and slide the crimp up to meet them.

With your chain nose pliers, flatten the crimp so it makes secure contact to hold the wires. For the best appearance, there should be no space between the wire guard and the flattened crimp. Make sure you do not compress the tiny tubes of the wire guard as you flatten the crimp.


Step 2) String on beads:
Holding the two wires together, string one colored bracelet bead, then one metal rondelle, and then one 3mm round metal bead and slide them up to the crimp. Now split the wires and string one metal tube onto each one and slide them up to the 3mm round metal bead.

Hold the two wires together again and string on one 3mm round metal bead, one metal rondelle, one bracelet bead, and one heishi. Continue to alternate bracelet beads and heishi for a total of two, three, or four sets. Then add the focal bead, followed by enough bracelet beads and heishi to match the first side, ending with a bracelet bead.

You can adjust the size of your bracelet by the number of beads added in the center on either side of the focal bead.

String on a rondelle metal bead directly after the last bracelet bead, and then string on a metal 3mm round. Now split the wires again and string one metal tube onto each.

The bring the wires together again and string on one 3mm round bead, one rondelle, one colored bracelet bead, and finally, the second crimp.

Step 3) Add second wire guard and attach to clasp:
Make sure all beads are strung evenly and without spaces, showing bare wire as little as is possible. Separate the two wires coming out of the second crimp and feed one up through one side of the second wire guard, across the top of the wire guard, and down through the second side.

Now slip the second ring of your magnet clasp over the piece of beading wire that you just fed through the second side of the wire guard and bring it up into wire guard so it rests around the u-shaped channel. Once the magnet clasp is attached, bring the end of the beading wire back down through the crimp and the colored bracelet bead. Pinch the two tube portions of the wire guard together so they are touching.

Keeping the crimp in position against the last colored bracelet bead, pull the tail of the wire running through the wire guard until the gap is eliminated between the crimp and the wire guard.

You still have a second piece of beading wire going up through the crimp. Bring this second piece of beading wire back down through the crimp, forming a loop. Then, reduce the size of the loop by pulling on the short piece of the second wire until there is just a small "nub" at the top of the crimp.

With your chain nose pliers, flatten the crimp so it makes secure contact to hold the wires. For the best appearance, there should be no space between the wire guard and the flattened crimp. Make sure you do not compress the tiny tubes of the wire guard as you flatten the crimp.

Step 4) Trim wires:
Carefully trim off the two short pieces as close as you can, one to the bottom of the flattened crimp and the other to the colored bracelet bead. Your tube bracelet is now complete.

Visit Anita's Beads and ask to see a demonstration at the counter if you need help.

Czech Glass Pearls

I am really loving the new Czech Glass Pearls just in at Anita's Beads. They are extremely affordable and come in a nice range of colors. I've been putting them to good use in some new Daily Bracelets!

In the 4mm size we have a very high quality version available in short strings of 31 pieces:

And here is another range of 4mm colors in a less expensive version which comes in strings of 120 pieces:

Here's what we have in the 6mm size:

Anita's lovely Czech glass pearls make an economical addition to your holiday gift and craft fair designs. Shop early for the best selection.

New Daily Bracelets

I've gotten back to wire work recently and am adding to the Daily Bracelet series using some of our new Czech pearls. I really love these orange ones for fall. Here is Daily Bracelet No. 47 with a matching necklace:

Here's another combination with some faceted Czech glass rondelles that remind me of blue Peruvian opal.
This is Daily Bracelet No. 46.